+ Reply to Thread
Page 1 of 2 1 2 LastLast
Results 1 to 10 of 12

Thread: Strengthening drivetrain, stripping slipper gears

  1. #1
    Lord_Inferno Guest

    Default Strengthening drivetrain, stripping slipper gears

    Hey everyone,
    I have a aon 6000kv with the mini inferno,
    i keep stripping the slipper gear! are the alloy gears any good?

    Any cures for my problems

    Thanks
    Adrian

  2. #2
    Four8s Guest

    Default

    Is your slipper locked? Are you Using 3Racing gears? Whats causing your slipper to strip?

    I was planing on getting alloy gears when I ran out of spurs, but Ive yet to strip any of them. On my stock spur I use the hard atomic slipper pad. with my 3racing spur I have a canter ball diff.

  3. #3
    Lord_Inferno Guest

    Default

    I was using delrin gears
    I'm using a alloy pinion
    And the rest of the drivetrain is standard

    The slipper was locked too!

  4. #4
    Four8s Guest

    Default

    How bout your motor mount? The stock plastic mount softens up and flexs under a hot motor, alowing the pinion to come out of alignment and wear out the spur.
    Also grains of sand getting between the gears will wear em out quickly too.
    Lastly, too much play between gears will also wear them out.

  5. #5
    Number_8 Guest

    Default

    Also, the center housing has a bit of a fault and you might want to get a 3Racing alloy one.

  6. #6
    Lord_Inferno Guest

    Default

    Has a fault in the centre housing?
    What i noticed was, the standard centre gear diff gear from the centre shaft going to the back diff was at times seperating from the actual gear piece.
    I wasn't too impressed haha!

  7. #7
    pimpsmurf Guest

    Default

    Nothing is wrong with the stock center bulkhead. That is BUNK!

    Are you using the stock motor mount? It's crap. Get an alloy one.

    I had trouble with it too, and here is the solution. Make absolutely sure that the gear mesh is perfect. Sometimes, even with the 3Racing alloy motor mount it, you need to use washers under the motor mount between the motor and the chassis to lift the motor up so you can get a good mesh. This is especially true with small pinions (13 or less) but on a 3 cell lipo w/ Aon4900 you can run 15-16 tooth pinions and even larger with a 2 cell or 8 cell nmhd.

    -JNY

  8. #8
    Hellgomes Guest

    Unhappy

    hi!!
    i have a problem like yours...
    (i have mamba and aon4900)

    My stock center diff never give me problems, but the front/rear diffs.....
    In first, the dog bones makes a big woles in the steel or in the titanium 3racing diff joints, i say BIG woles!!
    Than because this joints woles, theres the diffs problems.... plastic or derlin pinion is out of my plans, than i put the steel pinion, guess what... the diff have a better runtime, but the derlin "spur gear" blows again, but very better than the derlin pinion runtime lol (yes the pinion and spur gear is good sincronized)

    i dont have slipper but i put the 3r ball diffs to make a little slipper, and i think is not the very very best ideia.....


    resuming
    i have bought until now, about 4 joint complete kits, and very very diffs, st diffs and 3r diffs, and still searching for anithing better....


    sorry my poor english, and please give me a cure!!!!

  9. #9
    garrettsdad Guest

    Default

    Use MIP ball diffs F/C/R I also use thier cvds and outdrives, they stand behind their products and are great quality.... I am using the stock gear, stock center mount with the aon 4900 and 3 cell lipo..have had no problems at all........except my driving skills!

  10. #10
    Jrgunn5150 Guest

    Default

    I found using anything less than a 12 tooth pinion will strip everytime.

+ Reply to Thread

Similar Threads

  1. Slipper stripping
    By The_Yeti in forum General Discussion
    Replies: 4
    Last Post: 12-10-2006, 09:25 PM
  2. Atomic Slipper Gears
    By Huey808 in forum Parts and Hop-Ups
    Replies: 3
    Last Post: 06-01-2006, 04:36 AM
  3. Replies: 1
    Last Post: 05-01-2006, 12:10 PM
  4. New to the Half Eight, KEEP STRIPPING GEARS!
    By Nexxus in forum Parts and Hop-Ups
    Replies: 7
    Last Post: 02-18-2006, 12:57 AM
  5. 32T Slipper gear stripping
    By Huygee in forum Parts and Hop-Ups
    Replies: 0
    Last Post: 09-22-2005, 07:41 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts