+ Reply to Thread
Results 1 to 3 of 3

Thread: ...Mini Inferno Data...

  1. #1
    Join Date
    Mar 2005
    Location
    Tokyo, Japan
    Posts
    3,049

    Default ...Mini Inferno Data...

    ...This thread is locked...Its a READ-ONLY list of measurements and sizes etc...It is ever evolving...

    ...PDF Documents @ KYOSHO...
    http://www.kyosho.co.jp/web/downloa...f8_index-e.html

    ...Slipper Clutch Setting: 3.6mm-4mm...

    ...BEARING SIZES...*Courtesy of Hawk...
    Front diff : 4ea 6x10x3
    Rear diff : 4ea 6x10x3
    Center diff : 2ea 6x12x4
    slipper : 3ea 4x7x2.5 (EDIT: Now includes bearings sizes for the two optional units INSIDE the slipper clutch)
    slipper : 1ea 3x6x2.5 (small end)...

    wheel/axle : 8ea 4x8x3


    ...TOP screws (black) in front wheel hub @ 3x6...
    ...BOTTOM screws (silver) in front wheel hub @ 3x7...(these are hard to find...tape your screw holes so you dont lose these screws...) *KYOSHO now does these screws seperately...

    Stock Servo: KS-11

    ...SERVO MOUNT SIZES...

    KO/Futaba/Sanwa: 32.5x36x15 mm

    JR: 26.5x33x15mm

    Hitec: 30x29x13 mm...HS-85MG is a perfect fit...

    HS-85MG Mighty Micro Metal Gear (pretty much THE servo to run...)
    ...0.80 oz...(22.1 g) 0.51 x 1.14 x 1.18 in (13 x 29 x 30 mm) 41.7/48.6 oz-in (3.0/3.5 kg-cm) 0.16/0.14 sec @ 60 deg 3 pole ferrite motor, nylon gears, top ball bearing

    ...AON 4900 BL Motor Can @ 24mm...
    ...MAMBA BL Motor Can @ 20mm...

    ...KYOSHO MICRO BLOCK tires w/ spoked rims @ 95 grams...
    ...KYOSHO X-TREAD tires w/ spoked rims @ 90 grams...

  2. #2
    Join Date
    Mar 2005
    Location
    Tokyo, Japan
    Posts
    3,049

    Default Screw Lists

    ...Here is the screw lists 'stolen' from a pack of the red option screws...JPG coming too...First number is the SIZE, second number is the AMOUNT

    Self-Tapping (chunky thread) Button screws...
    2x6mm=4, 2.6X6mm= 11, 2.6x10mm= 1, 2.6x12mm=4, 2.6x14mm=6, 3x8mm=4, 3x10mm=3...

    Bind (shallow thread) Button screws...
    3x6mm=1, 3x8mm=4, 3x10mm=2, 3x12mm=6, 3x18mm=1, 3x20mm=4...

    Self-Tapping (chunky thread) Flat Head / Counter Sunk screws...
    2x4mm=16, 2.6x6mm=18, 2.6x8mm=25, 2.6x10mm=4, 2.6x16mm=2, 3x8mm=8...

    Flat head / Conuter Sunk screws (shallow thread)...
    2.6x6mm=2, 3x6mm=2, 3x8mm=3, 3x10mm=2...

    Self-Tapping Round Head screw...
    3x4mm=2...

    Truss screw...
    3x4mm=2...

    Set screw / Allen screw (the one that goes on with a hex tool (NB: In stock form these have NO hole to be used with a hex wrench)
    3x3mm=3, 3x6mm=5, 3x12mm=1, 3x16mm=2, 3x22mm=2, 3x25mm=3...

  3. #3
    Join Date
    Mar 2005
    Location
    Tokyo, Japan
    Posts
    3,049

    Default Borrowed From Kyosho

    ...for your referencing pleasure...


    ...BTW BitHed has this done and the best measurement I came up with was 0.5; Thats ONE 0.3 shim on first, followed by ONE 0.2mm shim

    ...plus the link kindly posted by Mr. Regan LeBlanc...

    http://www.kyoshoamerica.com/techtips/half8.asp

+ Reply to Thread

Similar Threads

  1. Suggestions on MIST Show truck
    By mathinstrument in forum Kyosho Mini Inferno ST
    Replies: 2
    Last Post: 02-02-2009, 10:44 PM
  2. The Ultimate Race machine
    By Rohit in forum General Discussion
    Replies: 17
    Last Post: 11-19-2006, 01:01 AM
  3. FS : Kyosho Mini Inferno H8. Full Option!
    By type r in forum halfEIGHT Marketplace
    Replies: 9
    Last Post: 03-21-2006, 03:49 PM
  4. Mini LST vs Mini Inferno ST ?
    By madgti in forum General Discussion
    Replies: 9
    Last Post: 11-16-2005, 07:12 AM
  5. A Mini Inferno Story.
    By Hammer in forum General Discussion
    Replies: 12
    Last Post: 08-02-2005, 10:17 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts