+ Reply to Thread
Results 1 to 6 of 6

Thread: Full ball bearing set

  1. #1
    MINITAY Guest

    Question Full ball bearing set

    Hi guys... this is my first post on this forum. I just bought the Mini inferno as well as oil filled shocks, Xspeed motor, full ball bearing and some other stuff.
    Maybe this is dumb but I don't know where to put some of the ball bearings.
    I don't know where to put :

    - The 2 biggest bearings.
    - 4 are the same size as the ones that go for wheels
    - 2 smaller bearings I don't about..
    - 2 tinny ones that seem to fit in many holes...

    Well I'd appreciate you guys tell me where I have to look...

    Thanks a lot !

  2. #2
    Join Date
    Mar 2005
    Location
    Tokyo, Japan
    Posts
    3,049

    Default

    ...mINItAY WELCOME TO THE BIG SHOW :d

    ...Check the H8 facts in the FAQ threads...The two BIGGEST bearings go on EACH end of the center diff...The SMALLEST goes in the REAR end of the slipper diff holes on the center hub...

    ...You have 4 the same size as the wheels? Do you have TWO in each wheel already? Sounds like you might not have a manual too...If you DONT grab it online from KYOSHO...There is a link in the FAQ...

  3. #3
    MINITAY Guest

    Thumbs up

    Thanks a lot Bithed I'm going to look at it right now !

  4. #4
    MINITAY Guest

    Exclamation Problem !!!

    Update
    I just received 8 cells the battery pack and decided to try the mini inferno with the XSPEED motor and smallest pinion to have an idea before installing the rest of ball bearings (differential). It runs great in forward but takes like 2-3 seconds before starting to go reverse. It does it even from a stop sometimes... pretty annoying.

    Well I didn't know that I had to take off all the pieces from the chassis to put the differential ball bearings... It doesn't seem to be an easy thing for me at least. Do you guys find it easy to put the differentials ones ? Any tips ?

    Thanks

  5. #5
    Hammer Guest

    Default

    Quote Originally Posted by MINITAY
    It runs great in forward but takes like 2-3 seconds before starting to go reverse. It does it even from a stop sometimes... pretty annoying.
    Have you adjusted the Throttle Trim on your Transmitter? That may help.

  6. #6
    mat3833 Guest

    Default

    yea, or your TX batts might be low. my mini t was glitching realy bad but it was because of the TX batts were low. the diffs are easy to take out, just look at your manual, it is in there.

    Matt

+ Reply to Thread

Similar Threads

  1. 4x8mm ball bearing in clutch shoe works great
    By tdrinc1 in forum Kyosho Mini Inferno 09
    Replies: 0
    Last Post: 01-30-2008, 10:13 PM
  2. general ball diff question
    By Nitrolio in forum General Discussion
    Replies: 2
    Last Post: 08-28-2006, 08:58 PM
  3. a few things I've noticed ( ball dif and drive cups)
    By auto2 in forum Parts and Hop-Ups
    Replies: 0
    Last Post: 02-19-2006, 04:08 AM
  4. Ball Bearing Maintenance/Cleaning
    By holy_inferno in forum Parts and Hop-Ups
    Replies: 14
    Last Post: 12-14-2005, 03:54 PM
  5. 3racing Aluminum Ball Bearing Steering Assembly
    By maxxenitout in forum Parts and Hop-Ups
    Replies: 3
    Last Post: 08-21-2005, 02:03 PM

Bookmarks

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts