Brushless Motors, Controllers, etc.
...The AON 4900...Its a direct fit...I run my wires over the top to use the gap in the shell..I tried them around the side but they would hit...From the top is a mUCH better fit... ...HPI RS4 12t pinion...Lots to grab onto...There is a the TINIEST gap between the grub / set screw and the idler...
Well I was running probably my third battery in my new Half 8, with my Mamba 8000 system in it, 6 cell integy 1400. I knew the motor was getting way too hot, but for now I just wanted to have some fun, I knew it was getting close to where I had to let it cool down, but I did a couple more laps,...
same as title, i dont want to get the wrong size pinion, who can i get them from? thanks
does brushless motor systems function in reverse or is there a reverse function in any BL system that would fit in the mini inferno? i've been searching on different websites, looking through all the BL systems they got and some sites say that the motor can go in reverse by switching any two...
Does anyone have this system in there mini inferno, i wanna know if this system is good. i'm lookin for mostly speed, i don't have a local dirt track so i want my inferno to be fast to run on concert tracks
How well do the brushless systems work with the NiHM 8 cell pack? Our local track does not allow LIPO.
im thinking of using a warp 4 in my MI. i will use a 11.1v li po set-up and a quark 33 amp. will this set-up be fine?
I've aquired a tekin 8000kv mini rage for my MIST and my question is with the pinion gear. Is the shaft on the motor smaller than other motors used in the MIST? The pinion fits very loosely and doesn't appear to spin true.I received two pinions with my MIST (I bought it used) and neither one...
Designed for the MI Motor designed for MINI INFERNO Kyosho , Micro RS4, Mini Truck 1/18 scale as NEW ASSO 1/18em. Can work with 6 to 7 cells GP 2000 or 2 Lipo cells, power up to 350 Watts, max 450 W / 5300 rpm/V. More info I'll order one soon with 6 or 7 cell GP2200 cells for my new, now...
For the guys running brushless motors and Atomic alloy slipper gears, what pinions are you using that mesh good with the slipper gears? I've heard theres a problem with some pinions because they are 48p imperial system and the slipper gears are 48p metric system or vice versa or something like...
It is finally there: the Mamba Max for 1/10cars. Put this in your MI and tear your drivetrain apart :D more info here
Any body runnnig a wraith motor ? Hows the room or lack of for the wires and steering post. Is their any get up and go with this motor :)
Hey guys... just wondering if any of you out there have ever broken a motor shaft...? I just switched pinions from a 13T to an 11T on my Wraith motor in my Half 8 because of heat issues. The gear mesh was set properly and there was no binding in the drivetrain at all. I took it out for a...
Hi guys, I am thinking of to get rid of my ALign 430L 4050 and instead i'll going to make a new chassis next month with my Mamba 8000kv (or Dynamite CV 8000KV) on 6cell 4/5 gp2200 with the kyosho 12t pinion(the special version for brushless for 2mm shafts). Layout will be like the 1/10 touring...
Well congrats to all the members of Half Eight. I have learned alot about my new Mini Inferno and it's overall set up. I've been working with Troy from BPP for the last few months and have nothing but issuses and problems. Not with Troy by with various brushless and 11.1v setups. Troy every step of...
Hello, Just letting you guys know to not get GPMs 13, 14, 15 gear pinion sets. I have to get new pinions becuase the Set screws SHATTERED (not stripped, just shattered) in the gear and there is no way to get the screw out. $10 wasted...
See ad in Off Topic Forum. Great motor - CHEAP !!!
Anybody have any heat issues with the Mamba esc, wraith combo the esc gets hotter than the motor runnin 7 or 8 cell normal setting on esc. should I reset the esc. both front & rear diffs un hooked from driveline spin smoothly center dif also I think I'm runnin a 15 tooth pinion and atomic gears.I...
ok well i finally got paid so i have some money. im looking into some H8 stuff. mainly a new motor. my choices are the wraith, aon 4900, or the warp 2 turn. what is the best for a semi-tight track with a few big jumps?? im currently running a mamba 5400 and like the speed but would like more of it...
Hi guys, I received the .6 pinion today and tried to fit it on my Align motor. Shaftsize is okidoki but the gearmesh is different and won't fit at all!!. Shit happens :D I now ordered a metric 48dp pinion by Robinson and hope it will mesh better cause I am curious what the car will do with the...
Hello, Is a Quark 22a enough power to run through the Mini Inferno, or do I need the Quark 33a? I wanna run a AON 4900 on it, and I could save some money just buying the 22a if itll do the same thing...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules