Brushless Motors, Controllers, etc.
...The AON 4900...Its a direct fit...I run my wires over the top to use the gap in the shell..I tried them around the side but they would hit...From the top is a mUCH better fit... ...HPI RS4 12t pinion...Lots to grab onto...There is a the TINIEST gap between the grub / set screw and the idler...
Has anyone used this combination yet? I am wanting to delve into the Brushless world and not sure which setup would be best. I drive on a fairly hard pack track that is on the smaller side. Thought would be greatly appreciated. Pete
the motor is great planes 28-35-3900 it is a 3900kv motor with tons of balls,,, mamba esc ,,,, vendetta truggy,,, MI ST wheels/tires,,,, 19/41 gearing (final drive is 5.46:1) this thing made my truggy extremely fast and would cause it to flip over if I didnt take precise control over the...
I have owned the Tekin Rage Extreme for a few weeks now and i think the motor is getting way to hot to the point where it smells. I am using 1400 8 cell 9.6 volt packs and only getting about 3-4 minutes run time, I am using a 9 tooth RC18T pinion with MIP ball diffs I have tried using a higher...
Hi, I would like to upgrade the speed of my half8 and rc18t. I wanted to have some feedback before shopping. How the mamba 8k or tekin mini rage or wraith 7k be paired with quark33-mamba25-tekin esc ? Which one gives the optimal combo for half8 and rc18t ? :)
I was wondering what motor pinions I should be using for my wraith which should be here any day now. I was running a 12 tooth HPI micro pinion on my Hyperion./ Should this be fine with the wraith?
I was racing my ST for the first time this weekend. I have a Mamba controller and an Aon motor (insanely fast). However with the metal robinson mini pinions, I kept stripping out my little blue gear reducer slipper gear things. I put a push-on plastic pinion on and ran without any stripping at...
Would it be possible to run an H8 with much higher capacity batteries, say the ones used in 1/10th scale, with a more powerful bigger ESC and the most powerful motor that can fit in the H8 (whatever it might be). Would this make any sense whatsoever or would the engine simply get too hot or...
:mad: Geez I just dont understand..I ran 4 or 5 batt pack without any probs and as I was testing my new URC 52s (10cell gp1100) for the 2nd time and after 30 sec of runtime a thick amount of smoke was coming out the ESC, + the weather was really cold... :( I still have my Mamba 25 esc but will...
I want to build up a racer with this H8 and I am thinking the Brushless is the way to go. I need suggestions on what works best. Chances are it will be used on a 1/10th scale track so speed would be needed. I just need suggestions for Motor ESC combos, any other ideas like drivetrain upgrades are...
On the back of the 540 mamba 7700kv motor it says "2s lipo max". Is that still the max power I can use if I'm running it off a 65a Quark roadster? Will a 3cell lipo instantly kill this motor?
I mean, I know that no one ever puts a Mamba in a H8, but that's a given. But how about the ESC? I know that people go with the Quark usually, cause of cogging with the Mamba, but can it be fixed? I have heard a few people talk of ridding the Mamba of cogging with a little programming. Is that...
Hi Guys, I found an easy programmeble esc for my Align. I have tried the 540 conversion but it was dissappointing: torque and speed were flawlessy. I decided to sitck with my Align brushless so I bought this esc for it. Next step is to build a 9cells package to power my MI or a 11.1V li-po...
6800 motor only for sale $40.00 shipped
New to the forums, great info so far. I have a question on fitting my Mamba 6800 into my half8. The stock pinion does not fit on the shaft good, the hole is bigger than the shaft and when I tighten the grub screw down it makes it out of balance. I'm not new to RC, coming off of a 4 year...
is that to much in a half 8? i also have a 68kv so i dunno? i am gettin a mini inferno st for my birthday and i just have a few question, ok well how is the diff? is there any diff issue with the half 8? i had a mlst but diff issue was reallin bad, will the stock diff hold up with a 92kv c4 or a...
does it?? or does it need parts??..
i will be using this more on the park like going in mulch and stuf like that.
Which is better for dirt track racing? I've heard only awesome things about both, and I'm dead-set on the Quark 33A Pro-Car ESC, so what would be best for dirt track racing, and half-throttle cruising down the street (mostly racing, though)?
What do you think of this motor 540 size with 5070rpm and this esc or this one They are both heli-esc so it should be proportional control. Maybe I ll put this one in my MI with 6 GP2200 cells. Should be tearing the drivetrain apart :D
I have a Hyperion 6000 and currently run it with a 9 or 10 tooth I cant remember which. The car is quite fast but I have a 13 tooth pinion and was wondering if anyone has had experience with a higher tooth pinion on the Hyperion. A large problem with this motor is overheating and I do not want it...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules