Brushless Motors, Controllers, etc.
...The AON 4900...Its a direct fit...I run my wires over the top to use the gap in the shell..I tried them around the side but they would hit...From the top is a mUCH better fit... ...HPI RS4 12t pinion...Lots to grab onto...There is a the TINIEST gap between the grub / set screw and the idler...
i would like to see someone work some magic..and make a 540 motor conversion...o man..a ss5800 in the h8 would fly! freakin i say atleast 70-75 mph with wheelies! lol
will it fit in the h8? without any mods?
well, i bought a aon 4900 and a mamba 25 esc from Gregg, someone on thsi forum..and i know its not his fault....well i was pretty sure he didnt use the same radio as i am using which is a airtronics blazer sport.....and i installed everything.....i tried to recalibrate and reprogram the esc since...
Do brush less motor get hot? Compression to brush motor which get hotter or are the about the same?
How well do the brushless systems work with the NiHM 8 cell pack? Our local track does not allow LIPO.
Hi Folks, i've searched hi and low and can't find any anywhere. My head will explode soon. Has anyone got a link to where I can get them. Don't say ebay. I've search and only find the 540 size :( (.com & .co.uk) As seen HERE direct linik is very much appreciated. :(
Hello, The 3 connectors are included in the package when you buy the motor alone? Thanks :)
Hello everybody, I'm interseting by this new brusless motor Warp 4. Who is selling at B-P-P (http://www.b-p-p.com/proddetail.php?prod=dc_warp4). It's a 380 size motor, shaft 3mm. Warp4 Brushless motor: kv: 3880, Io=4.10A, R=0.012, Max RPM 40,000, Max A Cst. 32A ,Max W (5 min) 260W, Max A...
Dear all, how is the x-speed (or the rocket 400) compared with the cheapest decent brushless with a 6 gp1100 battery pack? I would like to go for a chep brushless but I'm not sure it is worthed. Thanks, active
I was just buying some parts for my heli when I saw this http://www.allerc.com/product_info.php?cPath=7_76_77&products_id=1577 What do you guys think?
So I heard over on the radiocontrolzone forum that novak is working on a sensored mini brushless setup. Does anyone have more information?
What is this with TROY!!!!! After 4 months and 45 emails (thousands with this f....cking spam filter of his address) and replies and sorrys and f>>>>ing unbelievable fake traking numbers and i dont remember what else is been a long time !!! i amount 340 USD on 9 of february from this order ...
trying to figure out what to get for my H8 am I correct in saying the mamba 4900 motor runs hot and the aon4900 doesn't? or is it the ESC causing the problem? I'm sold on the tekin mini rage and AON motor just cause I trust you guys but would like a little education too.:-)
Those of you with the Hyperion 600 and a 3Racing Alum motor mount - 1. Did you use the smaller mounting holes on the 6000 or the larger holes? 2. Neither seem to line up perfectly with the mount - did you have to enlarge the mounting holes on the 3Racing motor mount? 3. What size...
Just got the ST. When I spin the center diff - it hangs up slightly on one spot. If I loosen the center diff case - it s smooth. Something seems to be gettign tweaked very slightly with the diff case tightened all the way. Any ideas? By the way -no motor/pinion even installed.
Are you sure you guys with Hyperions 5K/6K - micro pinions. I am using an RC18T 10t pinion. I cant get a good mesh to save my live and I have owned 10 RC cars and been doing this for 10 years. Are we sure these are right???
For those of you out there with the Tekin Mini Rage ESC: 1. What does Timing Advance do for you and what is your set on? Mine is still on factory default 2&3. I am running Hyperion 6000K with 8 cells IB1200. I have set my Throttle Profile to #4 Aggressive profile convex. I had it on 3...
What causes the heat build-up with BL motors/ESC? (I know improper gearing can - so no need to discuss that point). Is it because the batteries (example 8 cell NIHM) can't deliver the current/amps needed? Is it because the ESC can't deliver the current/amps needed? Is a 7.4V Lipo better...
Just took out my Hyperion 6000 on my ST and put in a Align 430L 4050KV. Still running 8 cell IB1200, Tekin ESC, 11T. Speed runs up and down the street - looks to be as fast as my Hyperion (which was pretty fast). But temps on Align under 100 degrees - no heatsink, no fan. My Hyperion ran...
See ad in Off Topic Forum. Great motor - CHEAP !!!
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules