Motors, tuning, arms, cans, magnets...
I have my half 8 on the way along with bearings, oil shocks and a rear carbon fiber shock mount. I like carbon fiber. The next thing I will get is a good 8-cell saddle battery pack and a better servo as well as more carbon fiber. Then I will want to get a good motor, which I am sure I will have...
I received my 8-cell pack today so I put it on my peak charger while I soldered a Dean’s plug on my stock RX unit. Took it out side and it is definitely faster. My stock motor with an alloy mount is getting pretty hot as well as my RX unit. I checked it with my heat gun I use on my nitro trucks....
I listed a while back on this form about my servo not working with the stock electrics but everything else works and I could not find anything wrong with the servo when I took it apart. So I am considering up dating all my eclectics. What set up as far as a motor and speed controller do people...
Have not been here in a while to do racing my nitro trucks. Has any one come out with a new brush motor or any one find any new brush motors that work with the stock reviver and ESC? I see they have come out with some new brush less.
Hello fellow Mini Inferno'ers,(does that work? :p) Well I got my Wraith 7k motor today and ran it. But before I get to the review I would like to give a big thanks to Troy over at www.b-p-p.com. I've talked to him on the phone and he is a super cool and knowledgable guy. I was going over...
There isnt really an indication of the speed of any of these online, does anyone have information about which is fastest? Is there another brushed motor faster? I know I'll get many reccomendations to go brushless, so.....I dont need max speed, but I DONT want ANY cogging.
Hi I got my motor tonight and the wire connectors are totally different than the tekin ESC. what is the best way to get around this? also the shaft does not have a flat on it for the grub screw. have you guys made one? or just put a 2 MM pinion on and tighten it up?
...Here is the motor I believe, after MUCH discussion and umming and ahhing over hot can coffee and cigarettes, to be the stock motor... ...There is more on the PAGE than in the picture... ...Dont worry about what appears to be a heat sink on the diagram...a heat sink DOESNT come...
...ok...i have a theory that i needed to get out there before i started on it, plus i just needed to look like i was busy for about an hour ;) ...The motor is getting very hot...both brushed and brushless are getting very hot... ...this is what i think... ...The slipper is creating a...
Hi. I just got my new XXtra receiver and it says that I have to install capacitors on my motor. The x-speed already has these though right? Thanks.
Hello, This is my first EP buggy which my Dad gave me. I am worried that if I use this motor, my stock gears/differentials will break. What other options are there for Brushless and ESC? Lastly, if I use the Quark ESC, can I still use the stock transmitter and receiver? Is it plug and...
I think it`s a greate car! But even with the x-speed in it the acceleration is very slow! Anyone more then me that thinks so? The only thing i really imagined with the x-speed was that the car went a little faster, but not the fast that i thougt it would be... I`ll hope that the 8cell GP batteri...
I had a mamba 25 set up with a mamba motor (6800kv i think.) played it with 3 cell lipo and it was fast. took it home, cleaned it and a few weeks later i tried it again but the motor was real jerky. and it got really hot real fast that it melted the plactic protector on my work table. I...
Has anyone tried this motor in there HALF8? I am currently running a Rocket400 with 7 Intellect cells but my pack starts getting a little "soft" at the 6 minute mark (7 minute mains). I used to run the BAJA motor in my mini-t and it was fast!.. but.. it is physically smaller than the...
I need a little help. I know that there are two basic "mini" pinion sizes - 2mm and 2.3mm. The 2mm fit the Mamba line and the AON 4900 and the 2.3mm fit the stock motor and some BL motors like the MINI AC line, but what brands are what size. I think it would be helpful for people that are new to...
Here's a picture of my Mamba 6800 installed in the H8, loaded it down with LRP heatsinks and it doesn't get too hot at all. Very impressed wth this car so far :D ! I haven't got to run it much with the weather like it is down here in Southeast Louisiana, but it's given me the time to work on the...
Just picked up a Mini Inferno ST and would like to get a more powerful motor that I can just drop in. Figured I would go with the X-Speed motor from Kyosho. Anyone has had any experience comparing the Red (buggy) vs. Blue label (HT for ST) motors? Is the high torque motor and what I assume...
In the process of ordering some goodies for my newly aquired Mini inferno and would like to know people's thoughts on which motor to get, I will be running it on 8 cells (intellect 1200's) So which will be faster? Kyosho X speed Graupner Speed 400 6v Suggestions please....... :)
Recentley got a mini Inferno ST. Had a lot of fun since I upgraded the battery to Kyosho 9.6v 1100Mah battery set but would love a bit more power. I was thinking of going for the X-Speed motor at first and see how I got on. Is there anything else that will give me more speed without going...
had a few ?'s about brushless. 1) IS THERE A BREAK IN POCEDURE FOR BL MOTORS 2) DO BL MOTORS HAVE LONGER LIFE? 3) DO THEY NEED MAINTENANCE? 4) ARE REPLACEMENT PARTS MADE AVIALABLE 5) HOW DO I MAKE A MOTOR LAST ITS LONGEST, AND/OR PERFORM IT'S BEST thanks for looking, feel free to...
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules