ESCs, Radios, Servos etc.
I have created a compilation of readily available ESCs suitable for 1/16th scale and above. The link is to an Excel workbook with three spreadsheets. Note the tabs on the lower left when you open it. The ESCs are mostly designed for 1/10th scale, but most will fit well in 1/16th scale. There is...
Hello Ladies and Gentlemen, Before I start this review, I would like to thank Troy over at www.b-p-p.com. He has replied to dozens of my e-mails gladly and I've talked to him over the phone. He is happy to answer my questions and always has a positive, and super nice attitude. He even soldered...
A friend of mine did this mod, but he has a lot faster servo then mine,(gonna buy a faster soon) Erlier i used HS85. Now Hitec HS945-MG, a beast servo, not so much faster,but a lot stronger 12kg :D ... http://galleriet.hobby-site.com/bilder/servomodd1.JPG...
Hey all, My stock Mini Inferno stopped steering the other day so I took out the servo and saw that the gear on the servo is stuck pretty tight for some reason. Since I'm gonna go brushless soon, I have an HS-81MG and installed it. The only problem is that i dont know which way to install it....
Hey Everyone... I Have a pretty simple question.... The other night, I left My ST on The table with the shell off, My son got His paws on it and managed to break the antenna wire in half :eek: , My question is, if I soder the two halfs back together and heat shrink it, will it mess up the range ,or...
So I just got my Mini Inferno (Nano Dragon 2, but most of the stock bits are gone) all set up with a Wraith 7k, Mamba 25, 3s lipo and a JR R125 receiver. It's running an 11t pinion and has a roll-over antenna so the antenna wire wraps around it and dangles from the top about 5 inches. I'm using a...
I want to upgrade my KMI with a mamba 25 esc and AON 4900 do I need to upgrade also my receiver or I can keep the original one? Thanks all.
I just got a 3racing engine mount with the fan. Now since I understand I can run the RX off the same lead that is used for the ESC CH1. And the servo wire goes to CH2. Would it work if I put the fan wire onto the Batt slot on the RX??? Also its a Futaba 2ch RX.
What charger do you use and what amp do you charge you batteries at? Cheers
I need a new reciver, one that can have a BL motor and also a brushed one. I would like to stay with the stock transmitter/27mhz... thanks.
Will all that voltage harm or break my servo or receiver? Is there something I need to buy to regulate the voltage? I'm thinking of using a 27mhz am, or buy a spektrum DX2. My question came up because if I do end up getting a spektrum and burn out the receiver, its not that cheap to get a new one....
my tekin voltage cut-off dosent seem to work properly with 3cell lipo!!!! Any input would be great
Hi, does any one know if this combination will fit or is using a Hitec HS81MG servo with the servo saver off the Xray M18, I have looked on the Xray site and it only list's the servo end part of the servo saver for Futaba, KO, Sanwa, Xray and Airtronics. Could it that the Xray servo is actualy a...
What radios/receivers can be used on the Inferno 09 GP? Cheers
I'd like to see what settings you are using. So far I have 100% punch and changed my battery to a 0 for the rate and there was no cogging with a 14 tooth pinion.
What mini or small digital servos will fit into the MIST? Is anyone running a digital servo? Not looking at making mods for a full size servo at this time.
will the hs5245 fit in the mist
Tekin has new 1/10 BL ESC in the works. If someone wants to have just one type of ESC's across all kits - will these fit the H8 ?
Im going to be racing a mini inferno in the upcoming season and I want to get rid of the OE electronics, esc included. Obviously the HS81mg is the way to go along with my spektrum reciver. As far as speedo? I'll be running the xspeed motor and the SMC 8 cell pack. I was looking at the LRP...
hi, If I am running 8 cells pack, is stock servo okie for most application ?
Well killed my pretty much brand new MI yesterday. Only had a couple of batt packs through it. So looks like I am upgrading earlier than expected. Had a small amount of smoke come of the esc/receiver. mmm so the list is now- BL motor New ESC New Reciever (must work with the std controller or...
Will this m8 module work for the mini inferno arr it says mini z only but i dunno http://shop.tinyrc.com/product.php?productid=16572&cat=0&page=1
I'm running stock class, so I'll prolly use like a X-Speed or Graupner. I want an ESC with lots of adjustability. Any one that you guys recommend?
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules