ESCs, Radios, Servos etc.
A friend of mine did this mod, but he has a lot faster servo then mine,(gonna buy a faster soon) Erlier i used HS85. Now Hitec HS945-MG, a beast servo, not so much faster,but a lot stronger 12kg :D ... http://galleriet.hobby-site.com/bilder/servomodd1.JPG...
Hello Ladies and Gentlemen, Before I start this review, I would like to thank Troy over at www.b-p-p.com. He has replied to dozens of my e-mails gladly and I've talked to him over the phone. He is happy to answer my questions and always has a positive, and super nice attitude. He even soldered...
I have created a compilation of readily available ESCs suitable for 1/16th scale and above. The link is to an Excel workbook with three spreadsheets. Note the tabs on the lower left when you open it. The ESCs are mostly designed for 1/10th scale, but most will fit well in 1/16th scale. There is...
...This is weird...The Mini Z platform uses the KT-2 and KT-5 controllers with RTR...the Mini Inferno lists the KT-3 as its controller...So WHY then does KYOSHO list that their stock replacement antenna will fit the KT-3 AND the KT-7? What IS the KT-7? :confused: Just more stuff to look forward to...
...Its big and its nasty and its more than i would want to pay...In fact its probably overkill but never mind... Read about it here...
If you are looking for a full feature receiver for your Mini RC or even one that will run your 1/8 scale, this summer you will have to look no further... CC has aquired BERG. These guys are the cats ass in the plane side of things. They are the only guys that make recievers smaller than...
i need some answers regarding the use of micro servo's. these are not used much nor discussed much on mini-zracer so i thought i would check with the guys here who are used to seperate electronic components. here is the situation... i am building a 1:32 CRT using the mr-02 electronics (pcb)...
Well Ive been looking around for an esc to replace the stocker for the Half 8. Ive looked at the GM VR series and the Mtroniks and some others. All seem good candidates until I went to Team Tekins website. I saw the Rebel 2 and I knew from then It was perfect for the half 8. Quicktune one...
I bought this cheap charger (kinda regreted it) and the manual is poorly written. My question is... Plug in power jack, the power light turned on right away. I dialed to 800-1200mah setting. When I connect my batteries (8 x Intellect 1200mah 9.6v) to the front connectors, the slow light...
Using stock electronic with 8 x Intellect 1200mah batt. (9.6v) and Xspeed motor. Problem 1: When I squeeze the trigger all the way, I noted that the steering servo also steer slightly to the right... This happen everytime my speed is at full throttle. When the speed is at mid-way (trigger not...
Hello! H8 original servo has 4 wires... normal servos have only 3 wires (5V, GND, signal) ... do you know how a "4 wire" servo works? A normal servo read a square-wave signal on the signal wire, if the on pulse is 1.5ms long the servo moves to center position, if the on pulse is 1ms the servo...
Hi, i need to find the type or the name of the batteries connector used on the mini inferno. Because i will make a wire to connect the pack directly to my battery charger. I can't find this information nowhere. Anybody can help me and tell me where i can find it? Many Thanks.
Tx: Futaba 3PM Rx: Futaba R133F (27mHz) ESC: GM-Racing V6R Servo: Hitec 85MG Batt.: 8 x Intell. 1200mAH (9.6V)
Okay brothers and sisters, I bought a Futaba 3PM-FM Tx, Futaba 133F Rx, HG-85MG servo, GM-Racing V6R ESC... all ready to do the replacement. But then... how do I remove the stock ESC/Rx unit? Use brute force? I studied the schematic and I see no screw holding the ESC in place. (1) Is it...
HI everybody, i'm a proud owner of a Mini 777 with a few options (stock,bearings, X-speed...), and i'm about to buy a charger with GP 1100 batteries. I found those 3 at average the same price. Which one would you choose? - T2M Wizard Pro - Graupner Ultramat 25 - T2M Swallow Digital. ...
Hello! I've just brought a miniservo at my LHS... but I don't know how to use in on my MiniInferno :) I changed the servo mount, choosing the one labeled "H", but I need two screws to connect my servo: which ones? Could you please post a photo if you've my same servo on your H8? Thanks!!!
Hello, For anyone that already has their H8, could you please post the list of aftermarket servos that can be put into the H8 without any type of chassis modification? From what I have read, the H8 comes with different mounting brackets for different servos. We just need a list of what those...
I have this OMNI cheap-ish 20$ charger with deltapeak it says that it is a "Automatic Ni-MH/Ni-Cd" charger but when I am supposed to choose the numbers of cells it states: 2cell 2.8V 3cell .. 4cell .. 5cell .. 6cell .. 7cell 9.6V 8cell 11.2V The instruction says:
I got my Half8 on saturday (2 days ago) stuck in the x-speed ad the 8 cell NiMH pack. I charge the pack on my Hobbice Quick Field Charger mk2. The max I charge it at is 1 amp. I am getting horrible run times before the throttle starts pulsing though. My last run lasted 2 mins 48 seconds (yup I...
Hi Guys, Can anyone tell why my new mamba performance kit will not ecept a JR122 2ch 75mhz (AM) rX I have two and both did not work? I checked them with other car and worked fine. It would only work a seperate Hitec steering servo and not mamba's esc?
Hi. I just got my H8 today. I installed 3 racing CVD's, 3 racing shocks, and a xspeed. A couple minutes ago I got some AA's and put them in the radio and in the battery holders when I turned it on, the car did not move. The motor looked like it was trying to move, but it could not turn the...
I was wondering if anyone has tried these yet. The are only $21.75 and 95 cents for shipping. The specs don't look too bad. blue bird servo
Hello! An italian friend asked me to suggest him a better ESC for his MiniInferno... what can I suggest? Novak Spy is a good choice? I read it's limited to 4-7 cells, so won't it work with a 8cell pack? Another good ESC with reverse? He doesn't need a brushless ESC... Thanks
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules