Non-Electronic Parts and Hop-Ups
...KYOSHO MINI INFERNO PARTS LIST... ...CORRECT AS AT FRIDAY NOVEMBER 04... IH100 Shock Stay Set IH101 Arm Set IH102 Front Shock Set IH103 Diff Gear Set (TWO needed for ONE car) IH104 Diff Small Parts Set (TWO needed for ONE car; this set will probably hold the ENLARGED diff cups which...
The first batch of chassis's are done! The chassis will allow the motor to be located in the stock position or rotated 180 degrees and be mounted towards the rear of the car (as in the photos). This is only advantageous to people using a brushless motor due to the fact that the motor will need...
...Unleashed soon from CAW, URC and BitHed...Just in time for it to poop under your Xmas tree...
My name is Ronny, and I'm from Norway. This is my first post here. I race 1/8 buggy for Mugen Seiki, RB Mods, Racing +, Neo-buggy etc. I just had my Half8 with me to the 1/8 OR Euro warm-up in France, where I gave the car a real run for it's money on the 2005 Euro's track. The car is equiped...
Hey, I've searched on the internet, but I can't seem to find a motor mount that will fit the Wraith...could someone plz find me one ?
Hey, Well, my car is faster, just the acceleration is crap because the slipper kicks in with my grabby finger. Do you guys glue the slipper, or do you guys just get the alomic slipper pads?
Hi all I have posted here with some pics of my H8 which i just a basher Dont know where to start Well stock not doing it for me anymore well all most all stock, has a X-speed SP motor and wheel bearings... I have been doing alot of reading, here and other sites, my mind is getting...
I rec'd my AON 4900 and Mamba 25A combo recently and was set on using my existing Intellect 9.6v packs but just thought I'd have a look at how much aggro it would be to fit the 11.1v 2250mah lipos I use in my T-Rex helicopter. I have seen lipo conversions on the H8 before but they all had the...
Hi all, I doubt this will get me anywhere, but I'm desperately seeking a titanium colored aluminum front shock tower by 3Racing. I've got the titanium colored rear tower, though cannot seem to find the matching front anywhere anymore. Also looking for same color front C-hubs. Thanks :o
hey guys im hoping i get a response as lately its been pretty dead on this forum ive recenly purchased a few 3racing bits and browsing on here these seem to be the best brand to go for and best fitting i purchased the alu c hub and alu front knuckle arm and these dont seem to fit well...
I recently bought some MIP diffs for my Mini-Inferno. As I was looking at the instructions for the center diff, it notes it uses M6 bearings. What is the actual size of the bearing that is to be used?
when I roll my car on the ground it seems theres a point on my center diff that binds. If I roll the car slowly it binds enough that the wheels will stop spinning. I took my center diff out and same thing happens when I spin it with my hand. Does anyone know what may be causing this?
hey guys one of the xspede CVD's with 1/10 hub convertors had failed today the pin in the shaft flew out and does not hold in place now it was only the first time i had run them too is there a claim for a replacement on this part?? i purchased the part from RCmart has anyone tried getting...
Does anyone know if these are available anywhere else? http://www.hobbyetc.com/cgi-bin/item.cgi?part_id=45010
Several upgrades parts for the Mini inferno Half8 parts on Ebay
Could not find M2.6X6mm flat/countersunk scews (hex or philips) for my MI. The only thing I can find is M2.5 or M3 or 4/40". Does anyone have experience on those alternative sizes? or where can I find M2.6? Thanks.
Just picked up a used MIST the other day. Wondering how well a HSE/Xtreme/etc. setup would go against the KMRC? Figured the KMRC setup would come out cheaper since I wouldn't need MIP center diffs, new gears, etc. And anyone that is running the KMRC chassis, what spare parts would you...
I just picked up this pack today. It's another HEX for fitting 1/10 wheel adapter set. But this set is including Front/Rear Swing Shafts with the hex. I'll have some pix showing them fitting with my half8 later on today.
Hello guys im undecided about which convertors to buy for my inferno 09. The XSpede XSMF-01 ... 1/10 conversion or the CAW axles and hex!!!! ive searched on here and can really decided which ones are better, i beleive on the forum the CAW ones have the edge but i wanna be sure before i...
hello this is my first post here so be nice :) i just got a mini inferno off my friend, i had been out of rc for about a year, used to have a revo and hong nor crt. now am back with something for abit of fun. (also am from ENGLAND) i want to know what sites are the best...... rc mart looks...
Is it possible to run the KMRC center diff and slipper on the stock Inferno chassis? If it is possible how much modding would it take?
i want one. are their any available or going to be available?
I only use my H8 STs for playing/bashing. Clean and refill the oil shocks regularly. Any recommendations on springs, oil types and shock setup worth knwoing about to optimize my experience and reduc bottoming?
Does anyone know anything about this part? I'm wondering how easy it would be to mount up to the H8.
Use this control to limit the display of threads to those newer than the specified time frame.
Allows you to choose the data by which the thread list will be sorted.
Order threads in...
Note: when sorting by date, 'descending order' will show the newest results first.
Forum Rules