PDA

View Full Version : ...Mini Inferno Data...



BitHed
04-06-2005, 04:50 AM
...This thread is locked...Its a READ-ONLY list of measurements and sizes etc...It is ever evolving...

...PDF Documents @ KYOSHO...
http://www.kyosho.co.jp/web/downloa...f8_index-e.html

...Slipper Clutch Setting: 3.6mm-4mm...

...BEARING SIZES...*Courtesy of Hawk...
Front diff : 4ea 6x10x3
Rear diff : 4ea 6x10x3
Center diff : 2ea 6x12x4
slipper : 3ea 4x7x2.5 (EDIT: Now includes bearings sizes for the two optional units INSIDE the slipper clutch)
slipper : 1ea 3x6x2.5 (small end)...

wheel/axle : 8ea 4x8x3


...TOP screws (black) in front wheel hub @ 3x6...
...BOTTOM screws (silver) in front wheel hub @ 3x7...(these are hard to find...tape your screw holes so you dont lose these screws...) *KYOSHO now does these screws seperately...

Stock Servo: KS-11

...SERVO MOUNT SIZES...

KO/Futaba/Sanwa: 32.5x36x15 mm

JR: 26.5x33x15mm

Hitec: 30x29x13 mm...HS-85MG is a perfect fit...

HS-85MG Mighty Micro Metal Gear (pretty much THE servo to run...)
...0.80 oz...(22.1 g) 0.51 x 1.14 x 1.18 in (13 x 29 x 30 mm) 41.7/48.6 oz-in (3.0/3.5 kg-cm) 0.16/0.14 sec @ 60 deg 3 pole ferrite motor, nylon gears, top ball bearing

...AON 4900 BL Motor Can @ 24mm...
...MAMBA BL Motor Can @ 20mm...

...KYOSHO MICRO BLOCK tires w/ spoked rims @ 95 grams...
...KYOSHO X-TREAD tires w/ spoked rims @ 90 grams...

BitHed
10-10-2005, 04:35 AM
...Here is the screw lists 'stolen' from a pack of the red option screws...JPG coming too...First number is the SIZE, second number is the AMOUNT

Self-Tapping (chunky thread) Button screws...
2x6mm=4, 2.6X6mm= 11, 2.6x10mm= 1, 2.6x12mm=4, 2.6x14mm=6, 3x8mm=4, 3x10mm=3...

Bind (shallow thread) Button screws...
3x6mm=1, 3x8mm=4, 3x10mm=2, 3x12mm=6, 3x18mm=1, 3x20mm=4...

Self-Tapping (chunky thread) Flat Head / Counter Sunk screws...
2x4mm=16, 2.6x6mm=18, 2.6x8mm=25, 2.6x10mm=4, 2.6x16mm=2, 3x8mm=8...

Flat head / Conuter Sunk screws (shallow thread)...
2.6x6mm=2, 3x6mm=2, 3x8mm=3, 3x10mm=2...

Self-Tapping Round Head screw...
3x4mm=2...

Truss screw...
3x4mm=2...

Set screw / Allen screw (the one that goes on with a hex tool ;) (NB: In stock form these have NO hole to be used with a hex wrench)
3x3mm=3, 3x6mm=5, 3x12mm=1, 3x16mm=2, 3x22mm=2, 3x25mm=3...

BitHed
10-21-2005, 03:06 AM
...for your referencing pleasure...


http://img.photobucket.com/albums/v258/bithed/20051021_083024.jpg

...BTW BitHed has this done and the best measurement I came up with was 0.5; Thats ONE 0.3 shim on first, followed by ONE 0.2mm shim ;)

...plus the link kindly posted by Mr. Regan LeBlanc...

http://www.kyoshoamerica.com/techtips/half8.asp